How to Mount Pole on Roof? In most cases, the best place to place your wireless router is on the roof of your home or organization’s building. Every top is unique, so this guide can’t cover all possibilities! We’re just describing the options here. It is up to your super judgment to decide which method to use.
First and foremost – use extreme caution when working on the roof. Slipping or slipping can result in prolonged falls and serious injury or death. If you don’t like working on a roof, don’t do it.
Help! Check with your society to see if there are professional roofers, cable TV, telephone installers, or others with experience working in such areas. They are of two basic types. A flat roof is often the easiest and safest to work with. A pitched roof has a slope, sometimes very steep. Therefore, it is recommended to work only on low-pitched roofs. In the image below, the top row of awnings is the safest, but the bottom two rows of roofs are tricky and potentially dangerous.
Should Different roof coverings and seals observe on both roof types? All this protects and waterproofs the roof. The most important rule when installing on the top is not to drill holes in the ceiling. Even if the gap is properly plugged in, it will eventually leak and cause problems in the long run.
Chimney Fixtures
If you have a tall chimney on your roof, use one of two drill anchors to hold the pipe to the chimney, or use strap brackets to attach poles, poles, or lines. Can install it on the roof. It’s up to you to drill a hole in the chimney or not. Note: If your chimney is missing brick or mortar or looks bad, do not add anything. These typically work on flat or sloped roofs. How to Mount Pole on Roof?
Anchor Bracket
A typical anchor bracket consists of two V-shaped pieces of metal that attach to the chimney with screws and dowels. Kits may be available at Radio Shack or online. Not included in the kit. Your local hardware shop should be able to help you with this. You only need about 4-5 feet of the pole, but make sure it’s painted or galvanized to keep it from rusting. This method includes drilling a hole into the chimney and inserting a plastic anchor or lead sleeve into the hole. These sets are usually available at hardware stores. Then screw in the mounting brackets, and the dowels will hold them to the brick. Use two brackets as one is not strong enough. Attach the pipe or mast to the bracket and hang the wireless router on the pipe. How to Mount Pole on Roof?
Strap Mount
The Strap Mount attaches a steel strap around the chimney and tightens with a wrench to secure the pole bracket. Your local hardware shop should be able to help with this. Strap mounts are a great option for older chimneys with soft bricks as they do not require drilling into the chimney. Use two sets of straps and brackets as one group is not strong enough to hold the mast. Once the belt is wrapped around the chimney and tightened, you can attach the mast to the bracket and attach the WiFi router to the mast. How to Mount Pole on Roof?
Vent Extension
If you have a sturdy vent pipe from your roof, you can add poles to add height. There are many different mounts, but they all consist of a vent and two pieces of metal that screw around the mast and hold it tight. If you’re best, you might find one at your local hardware store or Radio Shack. A length of conduit, pipe, or antenna mast is not included in these kits and can be used. But, again, your local hardware store should be able to help you with this.
All you need is a pole about 4 feet long, but make sure it’s painted or galvanized to keep it from rusting. It’s important to note that it should only be attached to metal vents. Plastic or PVC vents are too weak to hold the mast. Over time, the wind will shake the mast and tear the plastic vents. Vents should protrude at least 12 inches from the roof when using poles longer than 4 feet. It allows the two vent mounts to be 10-12 inches apart. If your mast is only 1 or 2 feet long, you may only need one mount.How to Mount Pole on Roof?
Eaves Fastener
Attaches to the edge of a sloping roof where other methods do not work. It does not work on flat ceilings as it usually has no eaves. It is required to drill holes in the wooden supports of the roof. There are different kits with floor supports of different lengths.
As with all these installations, galvanized or painted antenna masts are required. Please ensure they are in good condition, as you will be attaching these to the moldings along the roof’s edge. Rotten wood does not support well and can cause brackets to fall off or cause further roof damage in high winds. To properly support the antenna mast, leave approximately one foot of space between the top mount and the bottom support. Space is required. This method is not recommended for very long masts. Masts up to 4-5 feet are fine.
Non-Penetrating Fasteners
This type of installation uses weights to attach the pole to the roof. No drilling or bolting is required. It is generally the recommended method if you don’t have a chimney or chimney, but you can also use it if available.
Satellite TV is available from many sources; there is also a non-penetrating mount for sloping roofs – it is mounted on the top and has flaps that fit on either side of the roof. It would help if you did the following:
Under the bracket, Use a rubber mat. It is to protect the roof from damage. Use concrete blocks or other weights to hold it in place. It might look sturdy without it, but the wind is powerful. I don’t want to drop this thing off the roof.
Conclusion
As a homeowner or building owner, use the method you are most comfortable with above. It’s your home! Read through the options above to find the one that works best for you. If you are still unsure, please check with your region. See what your neighbors use to mount satellite dishes, TV antennas, or wireless devices.
